Europe – ECC Opens 4 Public Consultations
On July 7, 2023 the Electronics Communications Committee (ECC) opened the following public consultations, accessible here and available...
top of page
Engineering Solutions & Electromagnetic Compatibility Services
A Division of Rhein Tech Laboratories, Inc.
Search
Desmond Fraser
- Aug 1
- 1 min
Brazil – ANATEL Issues Technical Requirements for IPv6 Compliance
On July 6, 2023, ANATEL published Ato No. 7971 approving the technical requirements to evaluate compliance for IPv6 protocol in...
6 views0 comments
Desmond Fraser
- Aug 1
- 1 min
Canada – ISED Opens Public Consultation on ANSI C63.10-2020 and C63.25.1-2018
The Department of Innovation, Science and Economic Development (ISED) in Canada opened a public consultation on the adoption of two ANSI...
0 views0 comments
Desmond Fraser
- Aug 1
- 1 min
Canada – ISED Publishes RSS-192, Issue 5
The Department of Innovation, Science and Economic Development (ISED) in Canada published Radio Standards Specification RSS-192, Issue 5,...
1 view0 comments
Desmond Fraser
- Aug 1
- 1 min
EU Standards Update: New ETSI Standards Recently Released
This is a shortened list of the new ETSI standards published during the past month: ETSI EN 303 687 V1.1.1 (2023-06) - (June 2023) - 6...
3 views0 comments
Desmond Fraser
- Aug 1
- 1 min
FCC and ISED Documentation References
Question: Many of our certification applications contain some of the same technical documents we have submitted in support of prior...
4 views0 comments
Desmond Fraser
- Aug 1
- 1 min
Certifying Limited Modular Devices
Question: We want to FCC certify a new line of wireless modules that cannot be tested in a stand-alone configuration. How should we...
0 views0 comments
Desmond Fraser
- Jul 5
- 2 min
Shielding Effectiveness (SE) Testing
Rhein Tech Laboratories offers SE testing to many different standards. The most common SE standard is IEEE 299. We can accommodate...
13 views0 comments
Desmond Fraser
- Jun 14
- 1 min
Achieving copper balancing and preventing warping during automated soldering on PCBs
When designing PCBs, various ways exist to achieve copper balancing and prevent warping during automated soldering. One common method is...
5 views0 comments
Desmond A. Fraser
- Feb 13
- 1 min
FCC 22-84 Bans Authorizations for Devices That Pose National Security Threat
On November 25, 2022, the FCC released FCC 22-84, a Report and Order, Order, and Further Notice of Proposed Rulemaking on “Protecting...
57 views0 comments
Desmond A. Fraser
- Feb 11
- 1 min
Do I Use Continuous Ground Plane My PCB Design to Meet MIL-STD-461 Standard?
Printed Circuit Board (PCB) interconnects to meet all regulatory standards, including MIL-STD-461F, must be routed to reduce noise,...
40 views0 comments
Desmond A. Fraser
- Feb 1
- 1 min
Which Test Method on RTCA DO160 Standard is Equivalent to MIL-STD-461G, CS101?
Section 20 of the RTCA/DO-160G standard is an equivalent test method to MIL-STD-461G, CS101 "Conducted Susceptibility, Power Lines and...
45 views0 comments
MultiPoint
- Jun 24, 2021
- 2 min
FCC Waiver Request Process
FCC waiver request process for a Part 15 device is explained in detail. Contact Rhein Tech for your FCC testing questions and requirements.
62 views0 comments
Hossein Nik
- Mar 10, 2020
- 1 min
Update on TCBC Spring Workshop
The Telecommunications Certification Body Council (TCBC) is hosting its spring 2020 Workshop from April 6 – 9 at the Marriott Inner ...
11 views
Hossein Nik
- Mar 2, 2020
- 3 min
The Issue of EMI in the Medical Industry
Between the years of 1979 and 1993, there were more than 100 reports of medical equipment failure attributed to EMI in the United States...
16 views
Desmond Fraser
- Feb 10, 2020
- 2 min
NIST Releases Cybersecurity Risk Management Draft for Comment
This month, NIST (the National Institute of Standards and Technology) published a draft document entitled Key Practices in Cyber Supply ...
10 views
Desmond Fraser
- Oct 13, 2019
- 2 min
Tricks to Eliminate EMI in High-Speed PCB Design
If there's one thing that PCB and EMC design have in common, it's that these designs are often left until the very end of the product ...
22 views
bottom of page